iwlwifi

From Gentoo Wiki
Jump to:navigation Jump to:search
This page contains changes which are not marked for translation.

Resources

iwlwifi is the wireless driver for Intel's current wireless chips. Correct operation requires support from the kernel's wifi stack and card specific firmware loaded at run time.

Kernel

To make it work some kernel configuration is needed. The driver supports 802.11a/b/g/n/ac (depending on the device), so IEEE 802.11 should be enabled.

IEEE 802.11

Activate at least cfg80211 (CONFIG_CFG80211) and mac80211 (CONFIG_MAC80211). For details see IEEE 802.11 section of Wi-Fi artice.

Device driver iwlwifi

Use this driver for Intel's current wireless chips. Set it as a module <M> as shown here. Also the correct DVM or MVM firmware option according to the Module column of the firmware table is needed.

KERNEL Options for Linux Kernel 4.19
Device Drivers  --->
    [*] Network device support  --->
        [*]   Wireless LAN  --->
            [*]     Intel devices
            <M>       Intel Wireless WiFi Next Gen AGN - Wireless-N/Advanced-N/Ultimate-N (iwlwifi)
            <M>         Intel Wireless WiFi DVM Firmware support
            <M>         Intel Wireless WiFi MVM Firmware support
Important
In case the driver is built into the kernel (<*>) instead as a module (<M>), also the firmware needs to be built into the kernel. See the section When using built-in configuration.
After changes on kernel configuration do not forget to rebuild the kernel.

After rebuilding the kernel and rebooting with this kernel, the selected options can be verified as follows:

user $zgrep 'IWLWIFI\|IWLDVM\|IWLMVM' /proc/config.gz
Note
Support for the /proc/config.gz file can be enabled through the Kernel/IKCONFIG support feature.

Firmware

Additional firmware for the individual device is needed as listed in this table. Contemporary firmware is always available in the sys-kernel/linux-firmware package. In case it is not in linux-firmware it might be found in device-specific sys-firmware/iwlxxxx-*ucode packages.

Upstream Intel instructions recommend[1] adding all iwlwifi ucode to the kernel image. This is recommended for convenience, however it will bloat the kernel slightly.

root #emerge --ask sys-kernel/linux-firmware

When using built-in configuration

In case the driver is built into the kernel (<*>) instead as a module (<M>), also the firmware needs to be built into the kernel.

KERNEL linux-4.19
Device Drivers  --->
            Generic Driver Options  --->
                Firmware loader --->
 
                    -*- Firmware loading facility
                    (iwlwifi-xxxx.ucode) Build named firmware blobs into the kernel binary
                    (/lib/firmware) Firmware blobs root directory
                    [ ] Enable the firmware sysfs fallback mechanism

In this case replace iwlwifi-xxxx.ucode with the exact firmware name. Some attention seems to be needed for FW_LOADER_USER_HELPER_FALLBACK.

Optional: savedconfig

The savedconfig USE flag could be set for Linux firmware in order to avoid unneeded stuff in /lib/firmware/.

As for example the Intel® Centrino® Advanced-N 6205 needs iwlwifi-6000g2a-ucode while anything else may be commented out or deleted.

FILE /etc/portage/savedconfig/sys-kernel/linux-firmwareTake care that version number is removed
iwlwifi-6000g2a-5.ucode
iwlwifi-6000g2a-6.ucode

In order to not lose these settings on next firmware update the version number needs to be removed:

user $cd /etc/portage/savedconfig/sys-kernel
root #mv linux-firmware{-20200316,}

Latest firmware version supporting device

Below is an incomplete list of the latest known firmware blob supporting a given chipset. Device names are retrieved using lspci.

Device name Firmware blob filename Firmware version
Intel Corporation Wi-Fi 6 AX200 (rev 1a) iwlwifi-cc-a0-77.ucode 77.ad46c98b.0

Network device names

Warning
This section is obsolete. See Udev#Optional: Disable_or_override_predictable_network_interface_naming for updated instructions.

Network device names such as eth0 or wlan0 as provided by the kernel are normally changed on system boot (see dmesg) by the /lib/udev/rules.d/80-net-name-slot.rules udev rule.

To keep the classic naming this rule can be overwritten with an equally named empty file in the /etc/udev/rules.d directory:

root #touch /etc/udev/rules.d/80-net-name-slot.rules


Testing

After a reboot with the new kernel or after loading the modules, the device can be checked for availability by using following methods:

/sys file system

Get the device name by listing the /sys/class/net directory contents using ls -al or the tree command (provided by the app-text/tree package):

user $tree /sys/class/net
/sys/class/net/
├── enp2s14 -> ../../devices/pci0000:00/0000:00:1e.0/0000:02:0e.0/net/enp2s14
├── lo -> ../../devices/virtual/net/lo
├── sit0 -> ../../devices/virtual/net/sit0
└── wlp8s0 -> ../../devices/pci0000:00/0000:00:1c.0/0000:08:00.0/net/wlp8s0

ip command

To obtain the device name and verify that the wireless card is detected, execute the following ip command:

user $ip addr
3: wlan0:   ...

ifconfig command

The ifconfig command is provided through the sys-apps/net-tools package. Use ifconfig -a to list all detected network cards, even those that are not enabled/active yet:

user $ifconfig -a
wlan0     ...

A network card can be activated as follows:

root #ifconfig -v wlan0 up
SIOCSIFFLAGS: Operation not possible due to RF-kill
WARNING: at least one error occurred. (-1)

In this example, enabling the wireless card failed as a radio frequency kill state is set (usually to keep power consumption at bay and not connect by accident to a wireless network).

iw command

If the wireless network card driver supports the nl80211 stack, then the iw command as offered by the net-wireless/iw package can show the detected wireless cards:

root #iw dev
   phy#0
	Interface wlan0
		ifindex 4
		type managed

modprobe and modinfo

modprobe should return nothing:

root #modprobe iwlwifi

Most information about the driver module can be obtained by modinfo iwlwifi:

user $modinfo iwlwifi

lspci

lspci should display iwlwifi for both Kernel driver in use: and Kernel modules:.

root #lspci -nnkv | sed -n '/Network/,/^$/p'
03:00.0 Network controller [0280]: Intel Corporation Centrino Advanced-N 6205 [Taylor Peak] [8086:0082] (rev 34)
        Subsystem: Intel Corporation Centrino Advanced-N 6205 AGN [8086:1321]
        Flags: bus master, fast devsel, latency 0, IRQ 33
        Memory at f7d00000 (64-bit, non-prefetchable) [size=8K]
        Capabilities: [c8] Power Management version 3
        Capabilities: [d0] MSI: Enable+ Count=1/1 Maskable- 64bit+
        Capabilities: [e0] Express Endpoint, MSI 00
        Capabilities: [100] Advanced Error Reporting
        Capabilities: [140] Device Serial Number confidential
        Kernel driver in use: iwlwifi
        Kernel modules: iwlwifi

The xx:xx.x identifier will be useful for grepping specific information from dmesg.

dmesg

Check the output of dmesg. Replace 03:00.0 with the identifier from lspci and wlp with the network interface name.

user $dmesg | grep -i -E '03:00.0|wlp|iwl|80211'
[    0.251986] pci 0000:03:00.0: [8086:0082] type 00 class 0x028000
[    0.252146] pci 0000:03:00.0: reg 0x10: [mem 0xf7d00000-0xf7d01fff 64bit]
[    0.252863] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[    3.621978] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.629362] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.634986] iwlwifi 0000:03:00.0: enabling device (0100 -> 0102)
[    3.635111] iwlwifi 0000:03:00.0: can't disable ASPM; OS doesn't have ASPM control
[    3.644480] iwlwifi 0000:03:00.0: loaded firmware version 18.168.6.1 op_mode iwldvm
[    3.659269] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUG disabled
[    3.659270] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEBUGFS disabled
[    3.659271] iwlwifi 0000:03:00.0: CONFIG_IWLWIFI_DEVICE_TRACING enabled
[    3.659273] iwlwifi 0000:03:00.0: Detected Intel(R) Centrino(R) Advanced-N 6205 AGN, REV=0xB0
[    3.694543] ieee80211 phy0: Selected rate control algorithm 'iwl-agn-rs'
[    3.695812] iwlwifi 0000:03:00.0 wlp3s0: renamed from wlan0
[    5.060307] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[    5.352853] iwlwifi 0000:03:00.0: Radio type=0x1-0x2-0x0
[    5.431804] IPv6: ADDRCONF(NETDEV_UP): wlp3s0: link is not ready
[    8.908518] wlp3s0: authenticate with <my WLAN AP>
[    8.912238] wlp3s0: send auth to <my WLAN AP> (try 1/3)
[    9.016437] wlp3s0: send auth to <my WLAN AP> (try 2/3)
[    9.120455] wlp3s0: send auth to <my WLAN AP> (try 3/3)
[    9.125773] wlp3s0: authenticated
[    9.126019] wlp3s0: waiting for beacon from <my WLAN AP>
[    9.148418] wlp3s0: associate with <my WLAN AP> (try 1/3)
[    9.191232] wlp3s0: RX AssocResp from <my WLAN AP> (capab=0x1431 status=0 aid=2)
[    9.211860] wlp3s0: associated
[    9.242532] IPv6: ADDRCONF(NETDEV_CHANGE): wlp3s0: link becomes ready
[    9.249856] wlp3s0: Limiting TX power to 20 (20 - 0) dBm as advertised by <my WLAN AP>

Troubleshooting

Kernel not loaded

Check if the correct kernel is loaded. This can be accomplished as follows (depends on the IKCONFIG feature):

user $zgrep CONFIG_IWL /proc/config.gz

Firmware issues

  • For systems using udev or systemd, it is imperative to configure the kernel to load binary blobs. In this case the wireless card's firmware is the firmware that needs loaded. More information on configuring the kernel in this manner can be found in the following thread on the Gentoo forums: FW_LOADER_USER_HELPER_FALLBACK.

Wireless not working

KERNEL
Device Drivers  --->
    [*] PCI support  --->
        [*]   Message Signaled Interrupts (MSI and MSI-X)

No internet connection

If it is possible to connect to an access point, but not possible to connect to any server or get any connection to the Internet, it may be worth trying to disable 802.11n and/or enable software encryption. To do so, it is necessary to pass the parameter iwlwifi.11n_disable=1 or iwlwifi.11n_disable=8 and/or iwlwifi.swcrypto=1 to the kernel. In order to pass the parameter automatically on module load, the following file should be created:

FILE /etc/modprobe.d/iwlwifi.confDisabling 802.11n, enabling software crypto
options iwlwifi 11n_disable=1 swcrypto=1
Note
In newer kernels, inspected as of 5.3.7, setting 11n_disable=1 (or masked with 0x01) will result in 802.11ac being disabled. This will limit the device to a maximum of 54Mbit throughput.

Network crashes under heavy load

On some wireless cards (e.g. Intel® Wi-Fi 6 AX201), under heavy load, the network crashes with a similar error:

root #dmesg
[  367.411551] iwlwifi 0000:00:14.3: reached 20 old SN frames from 77:77:77:77:77:77 on queue 2, stopping BA session on TID 3

As a workaround, RX aggregation should be disabled using the kernel parameter iwlwifi.11n_disable=4:

FILE /etc/modprobe.d/iwlwifi.confDisabling RX aggregation
options iwlwifi 11n_disable=4

"Microcode SW error detected. Restarting 0x0" message in kernel logs

root #dmesg | grep iwlwifi
(... redacted ...)
[ 5711.326985] iwlwifi 0000:28:00.0: Microcode SW error detected. Restarting 0x0.
[ 5711.326987] iwlwifi 0000:28:00.0: Start IWL Error Log Dump:
[ 5711.326990] iwlwifi 0000:28:00.0: Transport status: 0x0000004A, valid: 6
[ 5711.326992] iwlwifi 0000:28:00.0: Loaded firmware version: 71.058653f6.0 ty-a0-gf-a0-71.ucode
[ 5711.326993] iwlwifi 0000:28:00.0: 0x00000071 | NMI_INTERRUPT_UMAC_FATAL    
[ 5711.326995] iwlwifi 0000:28:00.0: 0x00008210 | trm_hw_status0
[ 5711.326998] iwlwifi 0000:28:00.0: 0x00000000 | trm_hw_status1
[ 5711.327001] iwlwifi 0000:28:00.0: 0x004DAEA2 | branchlink2
[ 5711.327003] iwlwifi 0000:28:00.0: 0x004D9974 | interruptlink1
[ 5711.327004] iwlwifi 0000:28:00.0: 0x004D9974 | interruptlink2
[ 5711.327006] iwlwifi 0000:28:00.0: 0x0000C314 | data1
[ 5711.327008] iwlwifi 0000:28:00.0: 0x00000010 | data2
[ 5711.327009] iwlwifi 0000:28:00.0: 0x00000000 | data3
(... redacted ...)
[ 5711.329587] iwlwifi 0000:28:00.0: ieee80211 phy0: Hardware restart was requested

This indicates that a severe error has been encountered by the WiFi adapter's micro-controller which led it to be reset. Consequences might be network drop outs and/and severe slow downs even after the connection to the AP has been restored. The root cause might be difficult to point out (platform own radio noise/buggy firmware/etc) however one of the very first things to try, even if the power management has been disabled for the iwlwifi module, is to prevent the WiFi adapter PCIe link to go in power save mode. This is accomplished by changing the power_scheme value used by the iwlmvm module to 1 (active):

FILE /etc/modprobe.d/iwlmvm.confChanging power_scheme to 'active'
options iwlmvm power_scheme=1

Amongst additional countermeasures suggested on https://wireless.wiki.kernel.org/en/users/drivers/iwlwifi disabling 40 MHz channels usage on the 2.4GHz band might also help:

FILE /etc/modprobe.d/cfg80211.confTurning off 40 MHz channels usage (2.4 Ghz band)
options cfg80211 cfg80211_disable_40mhz_24ghz=Y

See also

External resources

References